Skip Navigation

rambos

@ rambos @lemmy.world

Posts
9
Comments
168
Joined
3 yr. ago

  • Newbie questions

    Jump

  • Correct and sounds like the best of both worlds

    I'll grab a kitchen sponge

    You can just cut 30x30 mm peace and zip-tie it over filament 😉

  • Newbie questions

    Jump

  • Enclosure will protect printer from dust and it will also keep the ambient temperature more stable. Dont make it hermetic sealed, better add few holes on the front and few on the back for example. I have a low rpm fan with dust filter because I mostly print PLA and in long prints (12h+) temperature can go a bit too high if there is no airflow at all. Keep in mind that enclosure should be removed sometimes for mintainance, removable sides is what you should look for.

    You can leave filament on the printer, but if you dont use it for a long time it could get wet and then you have to dry it. Keep the rest of the spools in plastic sealed box or bag and put some silica gel inside.

    Full calibration should be done once, but fine tuning when you face some issues or when you change to different brand or filament type. It depends how well the printer is assembled and how experienced you are, it can take only 5 min every few months, but begginers can spend days sometimes.

    Extra tips: clean your rails and wheels whenever you can (once a month at least) for dusty garage. Get a kitchen sponge, drill a hole in it and guide filament trough the hole to remove any dust before extruder.

    Welcome to the most fun hoby and happy printing!

  • Those who are self hosting at home, what case are you using? (Looking for recommendations)

    Jump

  • For 9 disks I would need to print a bigger case, but this one suits me well for now 😉

  • Going on a trip

    Jump

  • He is horny 😂

  • Should I use Restic, Borg, or Kopia for container backups?

    Jump

  • Daily backup to backblaze b2 and also to local storage with kopia. Its been running for a year I think, no issues at all. I didnt need a real backup yet, just did some restore tests so far

  • What's an elegant way of automatically backing up the contents of a large drive to multiple smaller drives that add up to the capacity of the large drive?

    Jump

  • If OP cant use more than one disk at once, how can they benefit from mergerfs?

  • Looking for low power devices for selfhosting

    Jump

  • In my country pi4 8GB ram with PSU 130€ and then you need SD card and/or SSD

  • Looking for low power devices for selfhosting

    Jump

  • Adding my data as well:

    My server is diy desktop pc - mbo MSI Z270-A PRO with celeron G3930 and 16GB RAM, 3x SSD on 550W PSU, idles at 23W. After adding another 3.5" HDD consuption went up to 34W. 34W in Ctoatia is around 34€ a year.

    Some SFF PCs are at 10-15W. SBCs like rpi should be below 10 W, but dont think you can get anything new for 80€

  • Sorry if this is covered somewhere but I couldn't find it! I need recommendations on a good starter NAS

    Jump

  • Your cpu supports quick sync so I bet you are good without gpu. Try it yourself before buying one, you also drain less power

  • Issues with layer adhesion (i think)

    Jump

  • -4c is extreemly cold, get thermometer inside of enclosure and leave your heatbed on until it reaches 10-15C before you start printing. Even better get enclosure heater. Id also bump nozzle temp to the highest marked on your spool.

  • Sharp corner algorithm

    Jump

  • Why lower if you print everything at the same layer height?

  • Sharp corner algorithm

    Jump

  • Interesting. This is new to me and it looks like it could work. It could be usefull if you print with 0.6 nozzle at 0.6 mm width and then in a corner narrow it down to 0.4 mm

  • The Perfect Linux Distribution

    Jump

  • Im not afraid of command line, but also dont feel like linux guy yet. The thing is that installing and using some distros are way easier than windows. I installed POP OS recently and cant believe how smooth and easy it was. Average windows users might not need command line at all on distro like that

  • Arrrgh what am I doing wrong?

    Jump

  • Casual users dont get on private trackers hehe. Joking, some guys were posting site that tracks when private trackers have open invites, hope someone will link again. Some trackers are almost impossible to join or keep up with their rules, but like torrentleech should be easy enough. Ive never used usenet since Im on private trackers for years, but I bet someone can recommend one here.

    You can look for older redit posts about recommendation for both, but first decide what contet you are aiming for. Some trackers are just for movies, some are focused on music, but there are also general purpose trackers like torrentleech.

  • 8BitDo’s $100 wireless mechanical keyboard screams ’80s NES

    Jump

  • Oh I love this one. How are gateron switches compared to MX? I had shitty romer g on logitech and replaced it with another one with MX and its day and night difference

  • Considerations for a homeserver thats open to the internet? (Jellyfin / Nextcloud)

    Jump

  • I went for wireguard VPN instead of exposing services. Its much more safe afaik, but you have to configure each device you want to give access (aka scanning QR code). You also dont need to buy a domain for that. Exposed services would be easier to use, especially if you want to use it on many devices

  • Do you share?

    Jump

  • Private trackers I seed until Im running out of storage, public ones up to 1.2 ratio.

    I used to upload some content, but dont have anything thats not already available anymore.

    I did some donations to our fellow pirates tho

  • Do you share?

    Jump

  • Better then pay for usenet instead of VPN. Not sure is 0% enough to protect yourself

  • Snapify: I built an open-source Loom alternative

    Jump

  • Thx for sharing, looks awesome

  • Piracy: ꜱᴀɪʟ ᴛʜᴇ ʜɪɢʜ ꜱᴇᴀꜱ @lemmy.dbzer0.com
    rambos @lemmy.world

    Good tracker for readarr?

  • Selfhosted @lemmy.world
    rambos @lemmy.world
    SOLVED

    Cant access local services when using VPN (AirVPN)

  • Selfhosted @lemmy.world
    rambos @lemmy.world

    Access local services when using VPN (AirVPN)

  • Linux @lemmy.ml
    rambos @lemmy.world

    Hide virtualisation from virtual machine

  • PC Master Race @lemmy.world
    rambos @lemmy.world
    SOLVED

    Is this normal power consuption on idle?

  • Piracy: ꜱᴀɪʟ ᴛʜᴇ ʜɪɢʜ ꜱᴇᴀꜱ @lemmy.dbzer0.com
    rambos @lemmy.world

    Do I need antivirus program?

  • 3DPrinting @lemmy.world
    rambos @lemmy.world

    Mini PC case

  • Android @lemmy.world
    rambos @lemmy.world

    Setting Alarm from Home Assistant

  • homeassistant @lemmy.world
    rambos @lemmy.world

    Customize card for counters